The Missed Approach Point, the Non-Precision Approach Question That Trips Up Instrument-Rated Pilots, and Why the MAP Is Not Always Where You Think It Is
The missed approach point isn't always at the runway threshold - on non-precision approaches it may fall well short of it, and confusing it with the VDP has killed pilots.
The missed approach point (MAP) is the point in an instrument approach procedure at or beyond which a missed approach must be executed if the required visual references have not been established. On precision approaches, it aligns closely with the runway threshold. On non-precision approaches, it may be well short of it - and a large number of instrument-rated pilots carry the wrong mental picture into every approach they fly.
What Exactly Is the Missed Approach Point?
The MAP is the last moment a pilot is permitted to still be looking for the runway. After that point, if the required visual references are not established, the approach is over. No extensions, no extra seconds of searching. The missed approach begins immediately.
Most pilots learn instrument flying with a tidy mental model: fly the approach, reach the runway, either see it or go around. That picture holds reasonably well for ILS approaches, where the MAP coincides with the decision altitude (DA). The geometry of a standard 3-degree glide slope places the aircraft near the threshold at DA, so the mental model fits.
On non-precision approaches, it doesn’t.
How Does the MAP Work on Non-Precision Approaches?
Non-precision approaches - VOR, LNAV-only GPS, NDB - have no electronic glide slope. Without vertical guidance, there is no decision altitude. Instead, pilots descend to the minimum descent altitude (MDA) and fly level until visual references are acquired or the MAP is reached.
On these approaches, the MAP is defined by a geographic fix: a crossing radial, a GPS waypoint labeled MAPT on the moving map, or - when no fix is available - a time calculated from the final approach fix (FAF) at a specified groundspeed.
The MAPT is not always at the runway threshold. On many non-precision approaches it sits a meaningful distance before the threshold, with a visual segment between the MAP and the runway. That segment is designed to be flown visually; instrument guidance has ended, and the pilot maneuvers to land under visual conditions.
What Is the Visual Descent Point - and How Is It Different from the MAP?
The FAA publishes a visual descent point (VDP) on many non-precision approach plates. The VDP is an advisory point from which a normal descent from MDA to the runway can be made. If the runway is in sight at the VDP, the pilot can begin a standard descent and expect to land in the touchdown zone.
The VDP is not the MAP. It is not regulatory. It is a planning reference.
If the runway is not visible at the VDP, a geometrically normal landing becomes difficult even if visual contact is later established. That is the VDP’s practical warning: usable approach geometry is running out.
Pilots conflate the two frequently. The MAP is the hard regulatory limit. The VDP is an advisory checkpoint. Knowing which is which is not academic - it is operational.
What Happens if You Cross the MAP Without Visual References?
A concrete scenario illustrates the stakes. Flying an LNAV approach, the MAPT waypoint is 0.5 miles before the runway threshold. You descend to MDA. You’re in and out of the ceiling. You cross the MAPT without the runway environment in sight.
The only correct action: go around immediately, at the MAPT.
Continuing past the MAP without the required visual references means flying in IMC without authorization from the approach procedure. That is precisely the scenario that produces controlled flight into terrain (CFIT) accidents. The pilot had a legal out and chose not to take it.
The other side of this: if visual references are established well before the MAP - say, 2 miles out as the ceiling breaks - the MAPT becomes an academic point. The requirement is that visual references must be established by the time the MAP is reached, not exactly at it. Establish them early, and you may continue.
How Do You Calculate the MAP Using Timing?
When the fix defining the MAPT isn’t available - navigation equipment failure, or an approach specified in time from the FAF - the MAP is calculated by timing.
The approach chart provides a table: at a given groundspeed, the time from the FAF to the MAP is a specific number of minutes and seconds. Start the clock at FAF crossing and execute the missed approach when the timer expires.
One critical detail: the calculation uses groundspeed, not airspeed. Wind matters. Using the wrong value shifts the MAP in time. Too high a groundspeed, and the timer expires before the actual MAP position; too low, and the pilot believes more time remains than actually does. This math belongs at cruise altitude, during the approach brief - not in the descent.
How Should You Brief the MAP Before an Approach?
Identify the MAP before beginning the descent. Know what defines it. If it’s a fix, have the identifier in mind. If it’s a MAPT waypoint, verify it’s loaded and labeled correctly on the GPS. If timing may be needed as a backup, calculate the number at cruise altitude and have it ready.
This is not a task for the final descent. Attempting to identify the MAP while descending through a broken ceiling at MDA is too late.
Why a Missed Approach Is Not a Failure
The MAP reflects careful calculation of exactly where the safety margin ends on a given procedure. Reaching the MAP without visual references and going around is the instrument system working exactly as designed.
The dangerous version is continuing past the MAP because the runway feels close, or because the pilot doesn’t want to manage a new clearance. The numbers on how many CFIT accidents involve a pilot who had a legal out and declined to use it are sobering.
An instrument rating is built on the discipline of trusting the numbers. The MAP is a number, calculated by people who spent significant time working out where the margin ends. A pilot who acts on it has that margin. A pilot who pushes past it does not.
Key Takeaways
- The MAP is the last legal moment to continue looking for the runway; without established visual references at the MAP, the missed approach is mandatory - no exceptions.
- On ILS approaches, the MAP aligns with the decision altitude, typically near the threshold.
- On non-precision approaches (VOR, LNAV, NDB), the MAP is defined by a geographic fix and is frequently located before the runway threshold.
- The VDP is advisory; the MAP is regulatory. They are not the same point and must not be treated as interchangeable.
- When no defining fix is available, the MAP is determined by timing from the FAF using groundspeed - calculate this before beginning the descent.
Radio Hangar. Aviation talk, built by pilots. Listen live | More articles