The Graphical Forecasts for Aviation, the Product That Replaced the Area Forecast in Two Thousand Seventeen, and the Altitude Selector That Changes Everything About How You Read the Icing Layer
The GFA replaced the text Area Forecast in 2017 and gives pilots an interactive, route-based weather picture - here's how to read it correctly, including the altitude selector that most students get wrong.
The Graphical Forecasts for Aviation (GFA) is the official tool for visualizing forecast weather conditions along your entire route, at your cruise altitude, across a 15-hour planning window. It replaced the dense text-based Area Forecast in October 2017 and is available free at aviationweather.gov. Most cross-country students have either never opened it or are misreading a critical setting that makes the icing layer dangerously misleading.
What Was the Area Forecast and Why Did It Go Away?
For decades, the Area Forecast (FA) was a core product in every standard weather briefing. It was a text product - dense, compressed aviation shorthand - covering broad geographic zones across the contiguous United States. The country was divided into large regions: central states, southern states, northeastern states, and so on.
Decoding an FA took practice. If you were flying from Indianapolis to Pittsburgh, the FA might describe conditions across the entire eastern half of the country. Pulling specific corridor information required careful reading and cross-referencing with multiple other products. For a student pilot preparing for a first cross-country, it was often impenetrable.
In October 2017, the National Weather Service retired the text Area Forecast for the contiguous United States and replaced it with the GFA - same forecast information, now delivered in a visual, interactive format.
How Is the GFA Structured?
The GFA lives at aviationweather.gov and is updated regularly based on National Weather Service model runs. When you open it, you’ll see three primary controls:
- A map of the contiguous United States
- Selectable weather product layers along the interface
- A time slider across the bottom, running out to 15 hours from the current time in 3-hour increments
If it’s 10:00 AM, you can see forecast conditions at 10 AM, 1 PM, 4 PM, 7 PM, and so on. For most general aviation cross-countries, that covers your entire flight window plus a buffer. Knowing your destination will be clear at departure but MVFR by the time you arrive is exactly the kind of information that shapes a go/no-go decision. The time slider makes that visible in a way a text product could not.
How Do You Read the Flight Categories Layer?
The clouds and flight categories layer is the one you’ll use most. It shows forecast sky coverage and ceiling heights, color-coded by flight category:
- Green - VFR: ceiling at or above 3,000 ft AGL and visibility at or above 3 statute miles
- Blue - MVFR: ceiling between 1,000 and 3,000 ft, or visibility between 3 and 5 miles, or both
- Red - IFR: ceiling below 1,000 ft or visibility below 3 miles
- Magenta - LIFR: ceiling below 500 ft or visibility below 1 mile
If you’ve used an EFB like ForeFlight or Garmin Pilot, you’ve seen these categories as color-coded dots at airport symbols. The GFA extends that system graphically across the entire country - including terrain with no nearby weather reporting stations, which is most of the country between airports.
Clicking any point on the map produces a pop-up with the specific forecast for that location: sky coverage, ceiling height in feet AGL, and visibility. This is what turns the GFA into a route-planning tool rather than just a destination check. Click along your planned route every 50 miles or so and look for any degradation between departure and arrival.
A common mistake at every training level is treating weather as a binary condition - good at the destination or not. You can fly into deteriorating conditions midroute and find yourself where continuing forward isn’t safe and turning back isn’t comfortable. The GFA makes the entire corridor visible, not just the endpoints.
How Do You Use the Icing Layer Correctly?
The icing layer shows forecast icing intensity - trace, light, moderate, heavy - across the country. But icing exists in a band, not across the entire atmosphere. The top of an icing layer might be 12,000 feet; the bottom might be 4,000 feet. Whether you’re inside that band depends entirely on your cruise altitude.
The GFA icing layer has an altitude selector. You can examine conditions at 2,000 ft, 4,000 ft, 6,000 ft, 8,000 ft, and up into the flight levels. The shading on the map changes with every altitude selection.
Here is the most common mistake: a student pulls up the icing layer, sees light blue shading across the route, and moves on without checking what altitude is selected. The altitude selector may default to whatever setting a previous user left. If the last person was checking conditions at 12,000 feet and you’re planning to cruise at 5,500 feet, the display is showing you something completely irrelevant to your flight.
Before interpreting any icing information from the GFA:
- Deliberately verify the altitude selector is set to your planned cruise altitude
- Check one altitude band above your cruise level
- Check one altitude band below your cruise level
Your actual cruise altitude in flight won’t be exact, and you want to know what’s adjacent to your level.
The turbulence layer works identically - altitude-dependent, with the same altitude selector to verify before reading the display.
Where Does the GFA Fit in a Full Preflight Briefing?
The GFA covers the enroute forecast portion of a standard briefing sequence. It does not replace the full briefing. A standard sequence runs:
- Adverse conditions - know immediately if anything changes the whole calculation
- Synopsis - the big-picture weather pattern
- Current conditions - METARs at departure and stations along the route
- Enroute forecast - this is the GFA
- Destination forecast - Terminal Aerodrome Forecast (TAF)
- Winds and temperatures aloft
- NOTAMs - Notices to Air Missions
The best way to cover all of this and create a legal record of your briefing is to file through Flight Service at 1800wxbrief.com. Even after doing your own research, filing through the system documents your briefing and contributes to the PIREP network other pilots are relying on.
What’s the Right Order to Work Through the GFA?
A practical preflight sequence using the GFA:
Step 1 - Start with flight categories. Open the flight categories layer for your planned departure time. Step the time slider through your flight window and arrival. All green across the route and the full period? You have a solid baseline. Any blue or red along the route or within your flight window requires thorough investigation before a go/no-go call.
Step 2 - Check the icing layer at cruise altitude. Set the altitude selector deliberately. Verify it before reading the display. Check one band above, one band below.
Step 3 - Check turbulence the same way. Altitude selector set and verified first.
Step 4 - Cross-check with METARs. Compare actual current observations along your route to what the GFA was showing for the recent past. If the GFA forecast VFR at your departure airport an hour ago and the current METAR shows a 1,200-foot overcast, the model and the real atmosphere disagree. That doesn’t mean you don’t go - it means the forecast had error in this area, and you should weight the GFA’s forward forecast for that region more cautiously.
Step 5 - Find PIREPs. Pilot Reports from aircraft that flew through your area in the last one to two hours are real-world calibration for the model forecast. If the GFA shows trace icing at your cruise altitude and a pilot who flew through forty minutes ago reported moderate icing, trust the pilot.
What Does a Real-World GFA Analysis Look Like?
Consider a flight from central Ohio to western Pennsylvania - about 140 miles, planned cruise altitude of 7,500 feet, departing at 11:00 AM.
Opening the GFA: flight categories at 11 AM show green across the entire route. Stepping to 1 PM (estimated arrival) - still green. Good baseline.
Switching to the icing layer, altitude selector set to 8,000 feet - the nearest band to the planned cruise level. Light blue shading covers northern Pennsylvania and southern New York: trace to light icing forecast. Dropping the selector to 6,000 feet, the shading lightens and mostly disappears. So 7,500 feet sits right inside the forecast icing band.
That’s information, not automatically a no-go. The aircraft has no icing equipment. The question becomes whether the destination is reachable at 6,000 feet, below the forecast icing layer, with adequate terrain clearance. It is.
Checking PIREPs: a report from an aircraft eastbound at 8,000 feet through that area ninety minutes ago - trace icing in cloud, brief encounter, exited the icing in about ten minutes. That aligns with the GFA picture: a narrow band, not an extended layer.
The filed route: 6,000 feet, below the icing band, with a plan to monitor conditions enroute and a contingency if the freezing level drops. That is aeronautical decision-making built on actual data.
How Does the GFA Apply to the Checkride?
The Airman Certification Standards require demonstrating that you can gather weather information and make a reasoned go/no-go decision. The examiner isn’t testing whether you can recite METAR definitions. They want to see where you find the data, how the products relate to each other, and how you explain your reasoning.
The GFA is a product you can pull up live during the oral exam. Step the time slider. Set the altitude selector and explain what you’re looking at. Cross-reference with METARs and PIREPs. Narrate the decision. That demonstrates the practical weather literacy the ACS is testing - and the preflight habit that will keep you safe well past the checkride.
Full documentation for each GFA product layer is available through the National Weather Service Aviation Weather Center at aviationweather.gov. The FAA Aeronautical Information Manual, Chapter 7, covers how these products fit into the standard briefing sequence.
Key Takeaways
- The GFA replaced the text Area Forecast in October 2017 and is available free at aviationweather.gov
- The time slider runs 15 hours out in 3-hour increments - use it to see conditions at every point in your flight window, not just departure
- The altitude selector on the icing and turbulence layers must be deliberately verified before you read the display - the default setting may reflect a previous user’s altitude
- When the GFA forecast and a current METAR disagree, weight the model forecast for that area more cautiously; when the GFA and a recent PIREP disagree, trust the PIREP
- The GFA covers the enroute forecast portion of a briefing - it does not replace METARs, TAFs, PIREPs, or a full Flight Service briefing through 1800wxbrief.com
Radio Hangar. Aviation talk, built by pilots. Listen live | More articles