The Go-Around, the Three-Second Hesitation That Costs More Than the Landing, and the Technique Sequence Every Student Gets Backwards on the Checkride
Master the go-around with the correct technique sequence, decision triggers, and what checkride examiners are actually evaluating during rejected landings.
The go-around is one of the most misjudged maneuvers in general aviation. Most student pilots treat it as a failure. Examiners treat it as a demonstration of judgment - and judgment is what the checkride is measuring. Understanding when and how to execute a go-around is what separates pilots who land safely from pilots who salvage landings by force.
Why Do Pilots Hesitate to Go Around?
The hesitation comes from framing. Students arrive at training believing the go-around is a do-over, an admission that the approach didn’t work. That framing is exactly backward.
A go-around is a decision - a good one. The examiner on your checkride is not disappointed when you go around. They are relieved. A pilot who recognizes an unstable approach and commits early is demonstrating the kind of judgment the Airman Certification Standards (ACS) are designed to measure.
The dangerous moment isn’t the bad approach. It’s the three-second pause where you know you should go around and don’t act. Two seconds convincing yourself it’ll work out, another second reaching for the throttle - and suddenly you’re at 200 feet with full flaps, low airspeed, and not enough runway.
When Should You Decide to Go Around?
The working standard most experienced instructors use: if you are not on a stable approach by 500 feet above the ground, go around.
Stable means on centerline, on glidepath, on speed, and in a configuration you can land from. If any one of those conditions isn’t met at 500 feet AGL, you don’t have enough runway remaining to fix it and land safely. The ACS for the private pilot certificate has the stabilized approach concept built in, though it doesn’t prescribe a rigid trigger checklist.
500 feet feels like a lot of time. It isn’t. That altitude gives you roughly 10 to 15 seconds of flight remaining in a training aircraft. What it’s actually buying you is options. At 500 feet, a go-around is clean. At 50 feet, it’s a scramble.
Build this habit before every approach - state your go-around triggers out loud:
- High and unstabilized at 500 feet - go.
- Runway not clear - go.
- Significant bounce - go.
- Something just feels wrong - go.
That last trigger is real. You are allowed to go around because something feels off, even if you can’t name it. That instinct is your brain processing information faster than your conscious awareness can. Trust it.
What Is the Correct Go-Around Technique Sequence?
The go-around has four elements that happen in a specific order for a specific reason.
1. Full power. The throttle goes forward immediately - smooth and deliberate, but full. Everything else waits until the engine is making power.
2. Carburetor heat off. If carb heat has been on during the approach - and in most training aircraft it should be - it must come off before you can expect maximum power output. Carb heat routes warm, less-dense air through the intake, reducing engine performance. This step trips up a large number of students. Applying full power with carb heat still on produces sluggish climb performance; you’re fighting the aircraft with one hand tied.
3. Establish a positive climb attitude and confirm the aircraft is climbing. Hold the attitude that produces a positive climb rate. For most single-engine trainers, that starts at best angle of climb speed (Vx) to clear any close-in obstacles, then transitions to best rate of climb speed (Vy) for sustained efficient climb. Do not reach for the flap handle until you have confirmed a positive climb rate.
4. Incremental flap retraction. This is the step most students rush - and the step that causes accidents when rushed. If you’re at full flaps - 40 degrees in a Cessna 172, for example - you do not retract them all at once. Retract one notch, verify positive climb rate, then retract another notch and verify again. Work your way out of the full-flap configuration gradually.
At full deflection, flaps are generating a significant portion of your total lift in addition to all that drag. Suddenly removing all of that lift at low airspeed causes the aircraft to sink. At 40 to 50 feet above the runway, that sink goes into the runway.
For complex aircraft with retractable gear, the sequence is slightly different. Positive rate is your trigger for gear up - before flaps come up. Retracting gear eliminates more drag than anything else you can do without disrupting lift the way flap retraction does. Gear first, then flaps incrementally.
What Does the Examiner Watch During a Go-Around?
Examiners are evaluating specific things, and they know exactly what they’re looking for.
The decision. Was it made clearly and committed to without hesitation? Once you say “going around,” you go around. Changing your mind at 20 feet because you think you can still salvage the landing is the behavior that causes accidents - and examiners are specifically watching for it.
Power application and carburetor heat discipline. The sequence matters, and they know the sequence.
Aircraft control and right rudder. Left-turning tendencies - P-factor, torque, and slipstream - all push the nose left at full power and low airspeed. Right rudder is not optional on the go-around. Students who don’t anticipate this drift off centerline immediately.
Flap retraction sequence. Was it incremental? Was positive climb rate confirmed between each step?
Callouts. The ACS expects verbalization: “Going around, full power, carb heat off, positive rate, retracting flaps.” This tells the examiner your head is engaged, not just your hands.
What comes after. Do you re-enter the traffic pattern with intention? A pilot who goes around from an unstabilized approach and immediately sets up another unstabilized approach tells the examiner this is a pattern, not a correction.
How Do You Handle a Bounce on Landing?
The default answer in the vast majority of cases: go around.
A very small bounce - a few inches, still on the numbers, plenty of runway remaining, airspeed known and appropriate - has a reasonable case for flying it back on. But the moment a bounce sends you a foot or two into the air with an uncertain energy state, the right answer is a go-around.
A bounce means the approach energy wasn’t quite right at the flare. Trying to recover by chasing the aircraft back onto the runway creates a cycle: the nose comes down, the aircraft bounces again - possibly harder. That chain ends at bent nose gear at minimum. The decision should be clean: bounce is significant, going around, now. Hesitating, trying to land, then going around at the last second is the sequence that earns a notice of disapproval.
What Are the Radio Calls for a Go-Around?
At a towered airport, announce immediately on frequency: "[Callsign], going around." The controller needs to know - they may have traffic lined up behind you or crossing traffic on another runway.
At a non-towered field, same principle on the common traffic advisory frequency (CTAF): callsign, position, going around, intentions.
Announce first, then manage the aircraft, then make the fuller position call once you’re established in the climb. Do not wait until you’ve retracted the first notch of flaps to make the call. Practice the callout alongside the physical sequence - on the checkride, both need to run simultaneously.
How Do You Practice the Go-Around Before Your Checkride?
On the ground: Run through the sequence - carb heat off, full power, climb attitude, incremental flap retraction - until it’s reflexive before you ever need it in the air.
Before every approach: State your go-around triggers out loud. Make them specific. Make them yours. Building this habit makes the decision automatic when you actually need it.
In the air: Ask your instructor to call for a go-around without warning - at 200 feet, at 100 feet, at the flare. The examiner may do exactly that, and you need to execute without a moment of hesitation.
After every go-around: Resist the urge to treat it as a failure. The pilot who uses the go-around when the approach isn’t working is exercising better judgment than the pilot who salvages every landing by force.
The ACS names this skill “recognition of the need for a go-around and rejected landing.” The word recognition comes first. Without the recognition, flawless technique means nothing.
The FAA Airplane Flying Handbook and the Airman Certification Standards for private pilot are both free from the FAA at faa.gov.
Key Takeaways
- If you are not on a stable approach by 500 feet AGL, go around - you do not have enough runway remaining to fix it and land safely.
- The correct sequence is full power → carb heat off → establish positive climb attitude → incremental flap retraction. Rushing flap retraction at low altitude causes sink.
- Left-turning tendencies are significant at full power and low airspeed - right rudder is required on every go-around.
- The examiner is watching your decision, not your landing. Early, committed recognition of an unstabilized approach is what earns a pass.
- In a complex aircraft, retract gear first on positive rate, then flaps incrementally - gear retraction eliminates more drag without disrupting lift.
Radio Hangar. Aviation talk, built by pilots. Listen live | More articles