The CTAF Call, the Self-Announce Sequence at Non-Towered Airports, and Why the Silence on Your Radio Is Not the Same as an Empty Sky
Master the CTAF self-announce sequence at non-towered airports - what to say, when to say it, and why radio silence is never proof of an empty sky.
Radio silence on the CTAF frequency does not mean the pattern is clear. At non-towered airports, the Common Traffic Advisory Frequency (CTAF) is the system pilots use to build a shared traffic picture when no controller is doing it for them - and knowing exactly what to say, and when, is a core safety skill.
What Is the CTAF and Why Does It Matter?
At a towered airport, a controller handles sequencing, calls out traffic, and tells you who to follow. At a non-towered airport, that entire job becomes yours. No radar, no one calling the Piper on a two-mile final - just you, your eyes, and your radio.
The CTAF is not just an announcement system. It is how every pilot in the area builds situational awareness together. The key word is shared. These calls give other pilots actionable information they can use to construct a mental picture of where you will be over the next several minutes.
What Does a Complete CTAF Call Sound Like?
Every CTAF transmission has four parts: name the airport, identify yourself, state your position and intentions, then close with the airport name again.
A complete call sounds like this:
“Riverside traffic, Cessna six four seven papa, ten miles northeast, two thousand five hundred, inbound landing runway two four, Riverside.”
That single transmission tells anyone monitoring the frequency which airport you are heading to, your direction and distance, your altitude, the runway you intend to use, and what airplane you are flying. Compare that to what gets broadcast constantly: “Traffic, Riverside.” That call communicates almost nothing. The goal is not simply to announce your existence - it is to give every other pilot in the area enough information to build an accurate picture around you.
What Is the Full Self-Announce Sequence?
The sequence begins before you enter the pattern and does not end until you are clear of the runway.
Ten miles out - inbound call. Confirm the CTAF from your sectional chart or moving map, then transmit: “Riverside traffic, Cessna six four seven papa, ten miles northeast, two thousand five hundred, inbound landing runway two four, Riverside.”
Including altitude matters here. It tells pattern traffic whether you are converging on their level, still above them, or already descending to join.
Entering the pattern. Using the standard 45-degree entry to the downwind: “Riverside traffic, Cessna six four seven papa, entering left downwind runway two four, Riverside.”
Base leg: “Riverside traffic, Cessna six four seven papa, left base runway two four, Riverside.”
Final: “Riverside traffic, Cessna six four seven papa, final runway two four, Riverside.”
Clear of the runway. This call gets skipped constantly. Do not skip it. A pilot holding short waiting to depart needs to know you are off the pavement. It costs one radio call and it matters: “Riverside traffic, Cessna six four seven papa, clear of runway two four, Riverside.”
What Calls Are Required When Departing?
Departing pilots have responsibilities too. Announce your taxi intentions when heading to the runway, announce when you are taking the runway, and announce your departure direction. That way, someone five miles out on inbound knows you are about to roll. It seems like a lot of transmissions. It is. That is the point.
What Should Every CTAF Call Include?
A few elements belong on every transmission, without exception.
Always use the full airport name - at the beginning and the end. Some CTAF frequencies are shared between multiple airports in the same region. Using the airport name on every call eliminates ambiguity about who you are addressing.
State the runway and traffic direction on every call. Runway direction immediately tells opposing traffic whether you are heading toward each other or away from each other. This is the single most useful piece of information you can give.
Give position in specific, geographic terms. “Ten miles northeast, two thousand five hundred” gives another pilot everything needed to place you on a mental map. “Entering the pattern” with nothing else gives almost nothing.
Why Is Radio Silence Dangerous?
The most dangerous assumption in general aviation is treating a quiet CTAF as an empty sky.
There are aircraft operating at non-towered airports right now with no radio at all. Ultralights, gliders, older trainers, and some experimental aircraft are not legally required to carry a radio in uncontrolled airspace. Beyond that, some pilots make an arrival call and then stop transmitting, assuming they have heard everything they need to. The result: two airplanes on final for the same runway with no radio contact between them.
NTSB data shows a significant percentage of mid-air collisions in general aviation occur within five miles of a non-towered airport - in the traffic pattern, at low altitude, where energy and maneuvering margin are both at their lowest. The pattern is not a place to relax the scan because the frequency sounds quiet.
CTAF calls reduce the risk. They do not eliminate it. Eyes outside the cockpit, clearing turns on key pattern legs, and proper traffic discipline remain entirely your responsibility.
How Do You Handle Conflicting Traffic or No Response?
When you transmit and hear nothing back, you are making a blind transmission - broadcasting your intentions to anyone listening. Not everyone will respond. That does not mean no one heard you. Keep transmitting.
When you do hear conflicting traffic, resolve it verbally. If someone calls final for the runway you are turning base to, announce your position and ask directly:
“Riverside traffic, Cessna six four seven papa on left base two four, is that Cherokee on short final or did I miss a runway change?”
That is not a dumb question. That is exactly how the system is supposed to work.
If you arrive and hear traffic using the opposite runway, do not assume they are wrong. Wind at pattern altitude can differ from the surface wind. Noise abatement procedures may be in effect. A pilot may be working from old ATIS information. Announce yourself, state your runway choice, and coordinate verbally. The goal is separation, not winning an argument about runway direction.
What About “Any Traffic in the Area Please Advise”?
You will hear pilots broadcast this phrase when they arrive on frequency and hear nothing. The Aeronautical Information Manual specifically identifies this practice as unnecessary, because standard position reports already communicate the same information and more - with greater specificity. Use the standard calls. They work better.
How Do You Find the CTAF Frequency?
The CTAF is published on the sectional chart, in ForeFlight or whatever moving map you use, and in the Chart Supplement (formerly the Airport Facility Directory).
At many smaller airports you will also see the term Unicom, which stands for Universal Communication. At most of these airports the Unicom frequency and the CTAF are the same. The person answering on Unicom is typically the fixed base operator (FBO), not a controller - their role is to provide airport advisories and sometimes weather, not to issue clearances.
If no published CTAF exists for a small airport, the Multicom frequency is 122.9 MHz. Memorize that number.
What About Night Operations and Pilot Controlled Lighting?
Many non-towered airports use pilot controlled lighting (PCL). Runway lights are off by default and activated by keying the microphone on the CTAF a set number of times:
- 7 clicks - high intensity
- 5 clicks - medium intensity
- 3 clicks - low intensity
Lights stay on for approximately 30 minutes and then cycle off unless you re-key. This information is published in the Chart Supplement for the airport. Know the procedure before you are five miles out in the dark.
What Does the Airman Certification Standards Require?
The ACS (Airman Certification Standards) requires demonstrating proper communication procedures at non-towered airports. An examiner is not simply watching whether you transmit. They are evaluating whether your calls contain the right information, whether you are actively listening and incorporating what you hear, and whether your pattern entry, spacing, and sequencing reflect a pilot who built an accurate traffic picture from what was on frequency.
Making the calls and actually processing the information are two different skills. The ACS expects both.
How Can You Practice CTAF Calls Without Flying?
One of the most effective practice tools costs nothing. Bring a handheld radio to your practice airport on a day you are not flying. Tune in the CTAF and listen for 30 minutes from the parking lot. You will hear both complete, useful transmissions and lazy half-calls that give nobody anything to work with. After that session, your own calls will be sharper.
Saying calls out loud in the car on the way to the airport also works. Narrate your position reports as if you are already in the pattern. It feels ridiculous. It works. By the time you are actually in the airplane, the words are already there - and the radio becomes the tool it was always meant to be.
Key Takeaways
- Radio silence is not an empty sky. Aircraft without radios - gliders, ultralights, older experimentals - are legally permitted in uncontrolled airspace.
- A complete CTAF call names the airport, identifies your aircraft, states position and altitude, states runway and direction of traffic, and closes with the airport name again.
- The full self-announce sequence includes 10 miles out, entering downwind, base, final, and clear of runway - plus taxi and departure calls when departing.
- NTSB data shows a disproportionate share of mid-air collisions occur within 5 miles of non-towered airports, in the traffic pattern.
- If no CTAF is published, use Multicom 122.9 MHz. Pilot controlled lighting procedures are found in the Chart Supplement.
Radio Hangar. Aviation talk, built by pilots. Listen live | More articles