The Alternator Failure, the Silent Battery Drain Nobody Notices Until the Radios Go Quiet, and the Load Shedding Procedure That Buys You the Time to Land Safely

An alternator failure in a GA aircraft can drain your battery silently for 40+ minutes before you notice - here's how to catch it early and manage it.

Flight Instructor
Reviewed for accuracy by Matt Carlson (Private Pilot)

An alternator failure in a general aviation aircraft rarely announces itself with smoke or a bang. It happens quietly, switching your entire electrical load onto the battery without any obvious warning. By the time your radios go silent, you may have already been draining that battery for thirty to forty minutes. Understanding how to catch this failure early - and manage it systematically - is the difference between a routine divert and an emergency.

How Your Aircraft’s Electrical System Actually Works

Most single-engine training aircraft have two electrical power sources: the alternator and the battery. In normal operation, the alternator does all the work. It runs your radios, avionics, lights, and electric fuel pump while simultaneously keeping the battery topped off. The battery’s primary job is engine starting and backup power - that’s it.

When the alternator fails, everything switches silently to battery power. The radios keep working. The GPS keeps talking. The engine keeps running. Nothing feels wrong. That’s what makes this failure insidious.

How to Spot an Alternator Failure Before It Becomes a Crisis

The primary instrument to watch is the ammeter (or voltmeter, depending on your aircraft). In a Cessna or Piper trainer, the ammeter needle normally sits on the charge side - roughly at the twelve o’clock position or just right of center - when the alternator is running. An alternator failure moves that needle to the discharge side, where it stays. Every minute it stays there, the battery is draining.

In aircraft equipped with a voltmeter instead of an ammeter, watch the numbers:

  • Normal operating range: 13 to 14.5 volts
  • Below 13 volts: pay close attention
  • Below 12 volts: you are on reserve time and the situation is urgent

Some panels include a low-voltage warning light labeled ALT OUT or LOW VOLTS. That light is useful confirmation, but it activates at a threshold - by the time it triggers, you may have already been burning battery for several minutes. The ammeter has been telling you longer. Use both.

The Scan Habit That Catches This Early

The pilots who handle alternator failures well don’t have better reflexes - they have better scan habits. Build electrical instrument checks into your routine from day one, not just the standard “big six.”

Before engine start, turn the master on and check the ammeter. With no alternator running, it should show zero or a slight discharge. After engine start, it should swing to the charge side within about thirty seconds. If it doesn’t, you have a problem - which is exactly the right place to find it.

During runup, include one deliberate look at the ammeter as part of your electrical system check.

In cruise, every time you cycle through your instrument scan, give the ammeter one glance. One second. That’s how you catch the failure at eighty miles out instead of four miles out with a dead radio.

How to Reset the Alternator (And When to Stop Trying)

When you suspect an alternator failure, the first step in most aircraft is to try recycling it. Turn the master off and back on. In aircraft with a split master switch (like the Cessna 172, where the left rocker is BAT and the right is ALT), cycle the ALT side - or both, in the sequence your POH specifies.

Alternators can trip offline from a momentary electrical overload and reset cleanly. If the ammeter swings back to the charge side, great - keep watching it closely. If it drops back to discharge, the alternator is done for this flight. Stop trying to reset it and move to the next step.

One important exception: if your aircraft has an overvoltage relay that tripped the alternator to protect the avionics, do not attempt a reset. Putting a malfunctioning overvoltage alternator back online can send a voltage spike through your avionics. Your POH will distinguish this scenario from a standard failure - read it.

What Is Load Shedding and How to Do It

Once you’ve confirmed the alternator has failed and won’t reset, shift into load shedding: turning off every electrical device you don’t absolutely need to extend battery life.

Leave on:

  • Primary radio (for ATC communication or traffic pattern position calls)
  • Transponder
  • Required lighting, especially if approaching dusk
  • Primary flight instruments, if electrically powered

Turn off:

  • All unnecessary avionics and navigation systems
  • Autopilot
  • Cabin lights
  • Pitot heat (unless in icing conditions)
  • Electric fuel pump, if the engine doesn’t need it at cruise
  • Any GPS not serving as your primary navigation reference
  • Audio panel features beyond the basics

How Much Time Does a Battery Actually Buy You?

A healthy battery in a well-maintained Cessna 172 or Piper Cherokee holds roughly 25 to 30 minutes of usable electrical power under moderate load. With aggressive load shedding - bringing demand down to radios and transponder only - some pilots have extended that to 45 minutes. But that figure depends on the battery’s age and condition, which you cannot assess in the air.

Plan for 20 minutes. Treat anything beyond that as a bonus.

Twenty minutes is enough to land at an uncontrolled airport in visual conditions. If that’s where you’re headed, know the light gun signals before you need them. A steady green from the tower means cleared to land. Steady red means give way and continue circling. Acknowledge with wing rocks in daylight or by flashing your landing light at night. These procedures are in the Aeronautical Information Manual.

Why Glass Panel Aircraft Are a Different Problem

An alternator failure in a Garmin G1000, Dynon SkyView, or any integrated glass panel aircraft is more serious than the same failure in a steam-gauge airplane. The display units draw considerably more power than gyroscopic instruments, so the battery drains faster.

Your glass panel may have its own internal backup battery, but that backup has a limited runtime - often 45 minutes to one hour - and it’s separate from the main aircraft battery. Both can be depleting simultaneously after an alternator failure.

Know your specific installation:

  • Does the glass panel draw from the main bus or an essential bus?
  • Does your aircraft have an essential/battery/emergency bus for shedding loads?
  • How long does each power source last under reduced load?

This information is in your POH and may also be in the avionics installation manual if the glass was added as an upgrade. Fly the airplane you actually have.

What to Do If You’re IFR When the Alternator Fails

An IFR alternator failure is the scenario that gets instrument-rated pilots into serious trouble. If you’re 60 miles from your destination in solid IMC at dusk, your battery is draining faster than it would in a steam-gauge aircraft. A full ILS approach requires sustained radio communication, navigation power, and potentially approach lighting - you may not have enough battery to complete the approach and still have comms at minimums.

Declare the emergency immediately. Do not wait until things are critical. The moment you confirm the alternator has failed and won’t reset, tell ATC. Priority handling, straight-in sequences, and coordination with the destination airport all become available to you faster when you say the word “emergency” than when you say anything else. The paperwork afterward is not interesting. Getting to the ground is.

Preflight and Practice: Making This a Non-Emergency

Request a dedicated electrical failure lesson from your CFI if you haven’t had one. It’s straightforward: the instructor covers the ammeter, tells you to assume the alternator has failed, and you run the procedure. You determine how much time you have. You pick the nearest suitable airport. You land. The whole exercise takes about an hour and builds more practical system knowledge than many training flights.

Read the emergency and abnormal procedures sections of your POH for every aircraft you fly - not just the normal procedures. The specific checklist sequences for alternator failure, overvoltage, and essential bus switching are there, and they vary between aircraft.

The Airman Certification Standards for the private pilot certificate expect demonstrated understanding of aircraft systems and appropriate response to simulated equipment malfunctions. Electrical failures are on that list. Know your airplane at the level of understanding, not just checklist memory - so that when the scenario doesn’t match exactly what you practiced, you can still reason through it.


Key Takeaways

  • An alternator failure transfers your entire electrical load silently to the battery - the only initial indication is ammeter needle movement to the discharge side.
  • Watch the ammeter every time you scan your instruments; in voltmeter-equipped aircraft, below 13V warrants attention, below 12V is urgent.
  • Try recycling the alternator first; if it won’t reset and stay online, begin aggressive load shedding immediately.
  • Plan on 20 minutes of usable battery after confirmed alternator failure, regardless of what the specs say.
  • In glass panel aircraft and IFR conditions, declare the emergency early - ATC resources and priority handling are available the moment you ask.

Radio Hangar. Aviation talk, built by pilots. Listen live | More articles