Line Up and Wait, the Runway Clearance That Replaced Position and Hold in Twenty Ten, and the Incursion Statistics That Made the FAA Finally Match the Rest of the World
Line up and wait replaced 'position and hold' in 2010 to match ICAO standards and cut runway incursions - here's exactly what it means and how to use it.
The clearance “line up and wait” authorizes you to taxi onto an active runway, align on the centerline, and stop - but it is not a takeoff clearance. The FAA officially replaced “position and hold” with “line up and wait” on September 30, 2010, aligning U.S. procedures with international ICAO (International Civil Aviation Organization) standards and addressing years of runway incursion data tied directly to phraseology confusion.
What Does “Line Up and Wait” Actually Mean?
When a tower controller issues a line up and wait instruction, you are authorized to enter the runway movement area. You taxi onto the runway, align on the centerline, and stop. The takeoff clearance is a separate instruction that comes after.
A typical exchange sounds like this:
Tower: “Traffic Pattern one, runway two seven, line up and wait.” Your readback: “Runway two seven, line up and wait, Traffic Pattern one.”
State the runway. Repeat the instruction. Say your callsign. That sequence is not optional.
Why Did “Position and Hold” Get Replaced?
The problem was the word “hold.”
In U.S. aviation English, “hold” appeared in multiple contexts with conflicting meanings. “Hold short of runway two seven” means stop before the runway and don’t cross. “Position and hold” meant enter the runway and stop on it - the opposite action. For international pilots trained on ICAO standards, the word “hold” in “position and hold” signaled exactly the wrong behavior. They had been trained that “hold” meant stop, don’t cross.
ICAO had standardized on “line up and wait” well before the United States made the switch. Nearly every other country used that phrase. Pilots flying into the U.S. had to mentally invert the meaning of a word that otherwise meant don’t move. That’s a system built for confusion.
The phrase “line up and wait” solves this by being self-explanatory. It tells you exactly what to do in two steps: line up on the runway, then wait for a takeoff clearance. The action and the constraint are both in the instruction.
Why Readback Is Required, Not Suggested
The FAA requires pilots to read back all runway crossing and hold short instructions, as well as takeoff and landing clearances. This is in the Aeronautical Information Manual (AIM) - it’s a requirement, not a formality.
The readback is how the controller confirms you heard the correct instruction. If you read back the wrong runway, a good controller catches it and corrects you before you’re on the wrong pavement. If you skip the readback and an incursion occurs, the absence of readback is operationally significant - not just a paperwork issue.
Always include the runway number in your readback. On a checkride, your examiner will notice if it’s missing.
What Are the Most Common Line Up and Wait Mistakes?
Starting the takeoff roll before the clearance. The runway number is also part of the takeoff clearance format, so the brain sometimes fills in the rest and pilots begin rolling before the controller finishes speaking. Slow down. Listen to the complete clearance before you move.
Crossing the hold short line without an explicit instruction. A line up and wait is a specific, stated clearance. If you don’t have it, you don’t cross. It is never implied by context.
Rolling because the runway looks clear. The controller is managing traffic you cannot see from your cockpit. Wait for the explicit clearance regardless of what you can observe.
Reading back a clearance you’re not certain about. If you’re unsure what you heard, ask before you act. “Traffic Pattern one, confirm, line up and wait runway two seven?” Thirty seconds of clarification prevents an incursion.
What Should You Do While Holding in Position?
Workload goes up, not down, the moment you stop on an active runway. Scan for traffic. Monitor the radio. Stay ready to act immediately if the tower issues a go-around or clears landing traffic to your runway. Head up, eyes outside.
The FAA’s Safety Alert for Operators (SAFO 10017) - issued around the time of the 2010 transition - advises that pilots should not hold on the runway for more than 90 seconds without receiving their takeoff clearance. That figure is advisory, not regulatory, but the intent is clear: if time is passing and you haven’t heard anything, check in with the tower.
“Tower, Traffic Pattern one, holding in position runway two seven.”
That’s the call. Don’t wait indefinitely.
What Does a Complete Sequence Look Like?
Tower: “Traffic Pattern one, taxi into position, runway three six, line up and wait, traffic on a two-mile final.”
That last detail - “traffic on a two-mile final” - is situational awareness the controller is handing you. You know why you’re holding, and you know where to look.
Your readback: “Runway three six, line up and wait, Traffic Pattern one.”
You taxi to the centerline, stop, scan toward final approach, and listen.
Tower: “Traffic Pattern one, runway three six, cleared for takeoff.”
Your readback: “Cleared for takeoff, runway three six, Traffic Pattern one.”
Every clearance in that exchange has a readback. If anything is unclear, say “say again” before you do anything. Never guess on a runway clearance.
Why Does Precise Phraseology Matter Beyond Compliance?
Aviation built its communication system around precision because voice radio is imperfect. Words get clipped. Frequencies are busy. Accents vary. English is used by pilots who learned it as a fifth language.
Standard phraseology functions as the error-correction layer built into voice communication. When everyone uses the same words the same way, deviations stand out. A non-standard phrase is a flag. A complete, correct readback is a checkpoint confirming both parties share the same picture.
This is why the AIM dedicates substantial space to phraseology, and why the Airman Certification Standards (ACS) treats radio communication as an evaluated task - not background behavior. For the private pilot practical test, “Radio Communications and ATC Light Signals” is its own task area. The examiner will evaluate whether you use proper phraseology, complete all readbacks, and correctly identify runways in every clearance exchange.
How Should Student Pilots Prepare for Towered Airport Operations?
If most of your training has been at non-towered airports, get several sessions at a towered field before your checkride. The first time you hear a live line up and wait clearance at a busy airport shouldn’t be during your practical test.
Modern flight simulators - including desktop platforms - often include realistic tower environments. Use them. Practice the full sequence: ground clearance, taxi, runup, hold short, line up and wait, departure. When the words become automatic, you spend your cognitive bandwidth on scanning and situational awareness instead of trying to remember what to say.
A Few Additional Points
You can decline a line up and wait if you need to. If your runup isn’t complete: “Traffic Pattern one, not ready, need another minute.” Controllers can work with you. You are a participant in managing the airspace, not just a vehicle being directed through it.
If you receive a “hold position” or “cancel takeoff clearance” instruction while on the runway, comply immediately. These are urgent instructions and they carry exactly the weight they sound like they carry.
The NASA Aviation Safety Reporting System (ASRS) database is public. Reading actual reports from pilots describing runway clearance confusion scenarios is one of the most practical study habits any pilot can build - these are real accounts of exactly what goes wrong and why.
Key Takeaways
- “Line up and wait” replaced “position and hold” on September 30, 2010, aligning the U.S. with ICAO standards already used by most of the world
- The clearance authorizes you to enter and align on the runway - it is not a takeoff clearance
- Read back every runway clearance, including the runway number; this is required by the AIM and evaluated on checkrides
- If you’ve been holding in position for approximately 90 seconds without a takeoff clearance, check in with the controller
- Never begin your takeoff roll until you have heard and read back an explicit “cleared for takeoff”
Radio Hangar. Aviation talk, built by pilots. Listen live | More articles