Dead Reckoning, the Wind Triangle Every Student Solves on Paper and Forgets to Trust in the Air, and the Navigation Log That Turns a Route into a Plan You Can Actually Follow
Dead reckoning and the wind triangle are the foundation of cross-country navigation - here's how to calculate headings, groundspeed, and fuel burns step by step.
Dead reckoning is the method of calculating your position based on a known starting point, direction, speed, and elapsed time. Combined with the wind triangle, it lets you determine the precise compass heading needed to track a planned course over the ground - regardless of whether GPS is available. Every cross-country flight plan starts here.
What Is Dead Reckoning and Why Does It Still Matter?
The concept predates aviation entirely. Sailors used dead reckoning for centuries to estimate position at sea. The core idea: know where you started, know your speed and direction, track your time, and you know where you are.
For pilots, one variable complicates the calculation - wind. The air mass you’re flying through is itself moving, which means your airplane can be pointed in one direction while drifting in another. Your heading and your ground track are two different things unless the wind is calm or perfectly aligned with your course.
Understanding this distinction is the foundation of every cross-country you’ll ever fly.
How Does the Wind Triangle Work?
The wind triangle is a vector problem with three sides:
- Your true airspeed vector - the direction your nose is pointed and how fast you’re moving through the air
- The wind vector - the direction the air mass is moving and how fast
- Your desired ground track - the actual path you want to travel over the earth
The difference in degrees between where your nose must point and where you want to go is the wind correction angle. The E6B flight computer - mechanical, electronic, or software - solves this geometry for you. But understanding what the tool is calculating lets you catch errors when the answer looks wrong.
How Do You Calculate a True Course from a Sectional Chart?
Start with your sectional chart and a plotter - part ruler, part protractor. Draw your course line from departure to your first checkpoint. Align the plotter’s straight edge along the course line, find the nearest line of longitude or latitude where the course line crosses, and read the angle off the protractor.
That angle is your true course - referenced to geographic north. Write it in the true course column of your navigation log.
How Do You Convert True Course to Magnetic Course?
Your compass doesn’t point to the geographic North Pole. It points toward the magnetic north pole, which sits in a different location and shifts slightly over time. Magnetic variation is the angular difference between the two, and it varies by location across the country.
Sectional charts print dashed blue lines called isogonic lines, each labeled with its variation value. Find the one nearest your route and apply the standard memory aid: east is least, west is best.
- If variation is east, subtract it from true course
- If variation is west, add it
Example: True course of 123° with 7° west variation = 130° magnetic course.
How Do You Calculate Wind Correction Angle and Groundspeed?
Pull the winds aloft forecast from the National Weather Service before every cross-country. It provides forecast wind direction and speed at standard altitudes - 3,000 feet, 6,000 feet, 9,000 feet, and higher. Use the level closest to your planned cruise altitude, or interpolate between two levels.
With a cruise altitude of 4,500 feet, check both the 3,000-foot and 6,000-foot forecasts and split the difference.
Example calculation:
- Forecast winds: 220° at 20 knots
- E6B result: wind correction angle of 10° left, groundspeed of 115 knots
- 130° magnetic course − 10° = 120° magnetic heading
If the wind correction angle looks extreme - like you’re pointing well away from your destination - trust the math. The wind triangle doesn’t lie.
What Is Compass Deviation and How Do You Apply It?
Every individual airplane introduces small compass errors from its electrical equipment, metal components, and other magnetic influences near the panel. These are called compass deviation errors and they are unique to each aircraft.
A compass deviation card is mounted on the instrument panel near the compass. It lists major headings and tells you the actual compass value to steer in order to achieve each magnetic heading.
Example: To fly a magnetic heading of 120°, the deviation card says steer 119° on the compass. That is the number you set on your heading indicator after leveling off at cruise altitude.
The full conversion chain: True course → Magnetic course → Magnetic heading → Compass heading.
How Do You Calculate Leg Time on a Navigation Log?
Time equals distance divided by groundspeed. Use the E6B to solve it quickly.
Example:
- Distance to first checkpoint: 42 nautical miles
- Groundspeed: 115 knots
- Calculated time: approximately 22 minutes - round up to 23 minutes on the nav log
Precision here matters. Your estimated checkpoint arrival times are your primary tool for confirming position in flight. If a checkpoint arrives 2 minutes early, your actual groundspeed is higher than planned - probably a favorable wind component. If it arrives 2 minutes late, you’re slower than planned. Time is data. Keep estimates accurate so the data is meaningful.
How Do You Plan Fuel for a Cross-Country Flight?
Fuel planning runs alongside time calculations for each leg.
Example:
- Fuel burn at cruise power: 8.5 gallons per hour (from Section 5 of the Pilot’s Operating Handbook)
- 23 minutes ≈ 0.4 hours
- 0.4 × 8.5 = approximately 3.5 gallons for that leg
Do this calculation for every leg, total it up, then add your reserve.
FAR 91.151 establishes the legal minimums:
- VFR day flights: fuel to reach destination plus 30 minutes at cruise power
- VFR night flights: fuel to reach destination plus 45 minutes at cruise power
30 minutes is a legal floor, not a safety standard. Depending on the airplane, 30 minutes of reserve is roughly 4–6 gallons. Forecasts are forecasts. Winds can reverse. ATC vectors add miles. Climb phases burn more fuel than cruise.
Plan fuel stops to land with 30–45 minutes above the legal minimum already in the tanks. Know your airplane’s actual fuel burn from real-world experience, not just handbook numbers - older airframes with real cylinders and real carburetors often differ from published figures. Always confirm fuel quantity with a visual fuel check before engine start, not a gauge glance.
How Do You Use the Navigation Log in Flight?
The nav log is a working document, not a planning artifact you set aside after departure.
At every checkpoint, write down the actual time. Compare it to your estimate. If you planned 23 minutes and you’re arriving at 25 minutes, your actual groundspeed is around 108–110 knots - not the 115 you planned. Update your time estimates for remaining legs and recalculate fuel burn accordingly. A slower-than-expected groundspeed on a long flight may mean a fuel stop you thought you could skip is now worth making.
About 10–15 minutes into each cruise leg, verify actual groundspeed and confirm your heading is tracking the planned course line. Small early corrections are always easier than large corrections when you’re significantly off course.
What Is Pilotage and How Does It Work with Dead Reckoning?
Pilotage means confirming your position by visual reference to landmarks on the ground. You cross-check your sectional chart against what you actually see outside - a reservoir in the right location, a highway intersection where the chart shows one, a distinctive river bend.
The Airman Certification Standards for the private pilot cross-country task require you to demonstrate both pilotage and dead reckoning. They work together: dead reckoning tells you where you should be, pilotage confirms it.
Choose checkpoints that are unambiguous - major highway intersections, reservoirs, large city edges, distinctive terrain features. Avoid small towns that could be confused with another small town 20 miles away. If you’re second-guessing whether what you see outside matches your planned checkpoint, that uncertainty itself is information: look harder or recalculate.
When you’ve done the underlying work, a GPS failure means mild inconvenience. You know your heading, your groundspeed, and your last confirmed position. You know the elapsed time since your last checkpoint. You can keep flying with confidence.
Key Takeaways
- Dead reckoning combines heading, airspeed, wind correction, and elapsed time to estimate position - it works whether or not GPS is available
- The full heading conversion runs: true course → magnetic course (apply variation) → magnetic heading (apply wind correction) → compass heading (apply deviation)
- Leg time and fuel burn must be calculated for every segment of the route, using actual groundspeed from the E6B and the POH fuel burn figure confirmed against real-world experience
- FAR 91.151 sets 30-minute VFR day and 45-minute VFR night fuel reserves as legal minimums - experienced pilots treat these as floors, not targets, and plan fuel stops with additional buffer
- Build the full navigation log on every cross-country, even when you intend to use GPS throughout - the planning process reveals problems on the ground where they’re easy to solve
Radio Hangar. Aviation talk, built by pilots. Listen live | More articles